Fabcam1 at 21:25, 4 June 2014

2014-06-04T21:25:45Z

Fabcam1: Created page with "'''Bend-Tech 7x Wiki :: Single Part -Interface/General Functions :: Adjust Centerline''' NOTOC 400px The Adjust C..."

2014-06-04T21:25:05Z

Created page with "'''Bend-Tech 7x Wiki :: Single Part -Interface/General Functions :: Adjust Centerline''' __NOTOC__ right|400px The Adjust C..."

New page

'''[[Main Page|Bend-Tech 7x Wiki]] :: [[Single Part -Interface/General Functions]] :: Adjust Centerline'''
__NOTOC__

[[File:adjustcenterline_1.png|right|400px]]

The Adjust Centerline tool allows how the part measurements are interpreted and will apply these changes to the part design. In the part designers, parts are assumed to be based on centerline. This tool allows the current part dimensions to be from the inside or outside of the tube instead.

[[File:adjustcenterline_2.png|right]]
'''To change the Location and/or Location Type for a bend''', first select the bend by clicking on it in the part display. A menu will appear where the location and location types can be adjusted. Click on either of the drop down menus to choose new options.

Once a new location or location type has been chosen, a red preview reflecting the location changes will appear. The original part will be shown in green.

Click the '''Home''' button [[File:adjustcenterline_3.png]] to set the part preview to the default location and orientation.

Click the '''Zoom Fit''' button [[File:adjustcenterline_4.png]] to zoom all the way in on the current view of the 3D part display and fit it to the display frame.

The part model can be shown in either wire frame or as a solid shaded model. Click on the '''wireframe''' button [[File:wireframe.png]] to show the model in wireframe. Click on the '''shaded''' button [[File:shaded.png]] to show the model as a shaded part.

Check the box next to '''Display Original Part''' to have the original part shown after changes are made to the locations.

Click the '''Inside''' button [[File:adjustcenterline_5.png]] to set the locations for all of the bends to inside.

Click the '''Center''' button [[File:adjustcenterline_6.png]] to set the locations for all of the bends back to centerline.

Click the '''Outside''' button [[File:adjustcenterline_7.png]] to set the locations for all of the bends to outside.

Click the '''OK''' button [[File:adjustcenterline_8.png]] to take the location and location type adjustments and apply them to the current part design.

← Older revision		Revision as of 21:25, 4 June 2014
Line 7:		Line 7:


−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−	~~[[File:adjustcenterline_2.png\|right]]~~
	'''To change the Location and/or Location Type for a bend''', first select the bend by clicking on it in the part display. A menu will appear where the location and location types can be adjusted. Click on either of the drop down menus to choose new options.		'''To change the Location and/or Location Type for a bend''', first select the bend by clicking on it in the part display. A menu will appear where the location and location types can be adjusted. Click on either of the drop down menus to choose new options.

Line 32:		Line 12:


		+	[[File:adjustcenterline_2.png]]

Adjust Centerline - Revision history

Fabcam1 at 21:25, 4 June 2014

Fabcam1: Created page with "'''Bend-Tech 7x Wiki :: Single Part -Interface/General Functions :: Adjust Centerline''' __NOTOC__ 400px The Adjust C..."

Fabcam1: Created page with "'''Bend-Tech 7x Wiki :: Single Part -Interface/General Functions :: Adjust Centerline''' NOTOC 400px The Adjust C..."