Cutting the End of a Part - Revision history

Fabcam1 at 20:42, 5 October 2015

2015-10-05T20:42:44Z

Fabcam1 at 20:42, 5 October 2015

2015-10-05T20:42:11Z

Fabcam1 at 21:16, 9 June 2014

2014-06-09T21:16:40Z

Fabcam1 at 19:58, 5 June 2014

2014-06-05T19:58:10Z

Fabcam1: Created page with "The following are the steps to setting up the cutting the end of a "part" . Step 1) Select the "Cutting" tab. Step 2) Select the "New Cut" command button. Step 3) Select th..."

2014-06-05T14:10:52Z

Created page with "The following are the steps to setting up the cutting the end of a "part" . Step 1) Select the "Cutting" tab. Step 2) Select the "New Cut" command button. Step 3) Select th..."

New page

The following are the steps to setting up the cutting the end of a "part" .

Step 1) Select the "Cutting" tab.

Step 2) Select the "New Cut" command button.

Step 3) Select the tube you are going to cut. Note: The straight end of a bent part will have a blue PickPoint on it. Select this PickPoint. You will find our part turn green in color.

CutEnd1.png

Step 4) Select the dot(s) representing the tube section(s) that our part is going to be cut to. You will find the intersecting tubes will turn red.

CutEnd2.png

Step 5) Select the "Cut Complete" command button.

CutEnd3.png

Notice the intersection now has a black and a blue cut marks showing the inside and outside of the material where each meets the intersection part(s).

Step 6) Select the "Print" command button.

CutEnd4.png

The cutting templates can be called up at a later time by selecting them from the list shown.

@@ Line 5: / Line 5: @@
 '''Step 2:''' Select the '''"New Cut"''' command button.
-'''Step 3: Select the tube you are going to cut. Note: The straight end of a bent part will have a blue PickPoint on it'''. Select this PickPoint. You will find our part turn green in color.
+'''Step 3:''' Select the tube you are going to cut. Note: The straight end of a bent part will have a blue PickPoint on it. Select this PickPoint. You will find our part turn green in color.
 [[File:CutEnd1.jpg]]
-'''Step 4: Select the dot(s) representing the tube section(s) that our part is going to be cut to.''' You will find the intersecting tubes will turn red.
+'''Step 4:''' Select the dot(s) representing the tube section(s) that our part is going to be cut to. You will find the intersecting tubes will turn red.
 [[File:CutEnd2.jpg]]

@@ Line 1: / Line 1: @@
 The following are the steps to setting up the cutting the end of a "part" .
-Step 1) Select the '''"Cutting"''' tab.
+'''Step 1:''' Select the '''"Cutting"''' tab.
-Step 2) Select the '''"New Cut"''' command button.
+'''Step 2:''' Select the '''"New Cut"''' command button.
-Step 3) '''Select the tube you are going to cut. Note: The straight end of a bent part will have a blue PickPoint on it'''. Select this PickPoint. You will find our part turn green in color.
+'''Step 3: Select the tube you are going to cut. Note: The straight end of a bent part will have a blue PickPoint on it'''. Select this PickPoint. You will find our part turn green in color.
 [[File:CutEnd1.jpg]]
-Step 4) '''Select the dot(s) representing the tube section(s) that our part is going to be cut to.''' You will find the intersecting tubes will turn red.
+'''Step 4: Select the dot(s) representing the tube section(s) that our part is going to be cut to.''' You will find the intersecting tubes will turn red.
 [[File:CutEnd2.jpg]]
-Step 5) Select the '''"Cut Complete"''' command button.
+'''Step 5:''' Select the '''"Cut Complete"''' command button.
 [[File:CutEnd3.jpg]]
@@ Line 22: / Line 22: @@
 Notice the intersection now has a black and a blue cut marks showing the inside and outside of the material where each meets the intersection part(s).
-Step 6) Select the '''"Print"''' command button.
+'''Step 6:''' Select the '''"Print"''' command button.
 [[File:CutEnd4.jpg]]

@@ Line 7: / Line 7: @@
 Step 3) '''Select the tube you are going to cut. Note: The straight end of a bent part will have a blue PickPoint on it'''. Select this PickPoint. You will find our part turn green in color.
-CutEnd1.png
+[[File:CutEnd1.jpg]]
 Step 4) '''Select the dot(s) representing the tube section(s) that our part is going to be cut to.''' You will find the intersecting tubes will turn red.
-CutEnd2.png
+[[File:CutEnd2.jpg]]
 Step 5) Select the '''"Cut Complete"''' command button.
-CutEnd3.png
+[[File:CutEnd3.jpg]]
@@ Line 24: / Line 24: @@
 Step 6) Select the '''"Print"''' command button.
-CutEnd4.png
+[[File:CutEnd4.jpg]]
 The cutting templates can be called up at a later time by selecting them from the list shown.