Exhaust Tutorial - Revision history

Fabcam1 at 19:38, 10 December 2014

2014-12-10T19:38:12Z

2014-12-10T19:35:34Z

2014-12-03T15:57:15Z

2014-12-02T22:36:22Z

2014-12-02T22:34:30Z

2014-12-02T22:33:43Z

2014-12-02T20:29:58Z

2014-12-02T18:26:49Z

2014-12-02T18:24:23Z

2014-12-02T18:23:25Z

← Older revision		Revision as of 19:38, 10 December 2014
Line 1:		Line 1:
−	~~"'''UNDER CONSTRUCTION: THANK YOU FOR YOUR PATIENCE'''"~~
−
	'''This tutorial is designed to walk the user through the steps in making an exhaust system out of bent parts in the Exhaust interface. For initial information on the Exhaust interface, see [[Exhaust Design]]'''		'''This tutorial is designed to walk the user through the steps in making an exhaust system out of bent parts in the Exhaust interface. For initial information on the Exhaust interface, see [[Exhaust Design]]'''

← Older revision		Revision as of 19:35, 10 December 2014
Line 325:		Line 325:
	[[File:Exh_muffoffset4.png]]		[[File:Exh_muffoffset4.png]]

−	"'''For further information on the Exhaust Designer, see [[Exhaust Tutorial II]].'''"	+	'''For further information on the Exhaust Designer, see [[Exhaust Tutorial II]].'''

← Older revision		Revision as of 15:57, 3 December 2014
Line 293:		Line 293:


−	~~13. Select the~~ "'''~~Connect~~'''" ~~[[File:Exhaust_connect1.png]] button and click on each part in sequence from left to right to connect them.~~	+	*"'''The offset is complete.'''"

	[[File:Exh_partdefine2.png]]		[[File:Exh_partdefine2.png]]

@@ Line 246: / Line 246: @@
 . Select the "'''Next'''" [[File:Exhaust_next1.png]] button.
@@ Line 267: / Line 266: @@
 . Select the "'''Next'''" [[File:Exhaust_next1.png]] button.
@@ Line 287: / Line 284: @@
 . Select the "'''OK'''" [[File:OK_button1.png]] button on the last window and the outline for the offset part will appear in the display area.

← Older revision		Revision as of 22:34, 2 December 2014
Line 246:		Line 246:

	8. Select the "'''Next'''" [[File:Exhaust_next1.png]] button.		8. Select the "'''Next'''" [[File:Exhaust_next1.png]] button.
−
−


Line 277:		Line 275:


−
−	~~11. Name and save the offset specs to whatever you'd like.~~



		+	11. Name and save the offset specs to whatever you'd like.


Line 290:		Line 287:

	12. Select the "'''OK'''" [[File:OK_button1.png]] button on the last window and the outline for the offset part will appear in the display area.		12. Select the "'''OK'''" [[File:OK_button1.png]] button on the last window and the outline for the offset part will appear in the display area.
		+

← Older revision		Revision as of 22:33, 2 December 2014
Line 258:		Line 258:


		+	9. Don't change the any of the dies that are going to be used for these bends as long as they are set at "'''4.0'''" as directed in the beginning of this tutorial.


Line 264:		Line 265:


−	9. Don't change the any of the dies that are going to be used for these bends as long as they are set at "'''4.0'''" as directed in the beginning of this tutorial. Select the "'''Next'''" [[File:Exhaust_next1.png]] button.



		+	10. Select the "'''Next'''" [[File:Exhaust_next1.png]] button.


Line 275:		Line 276:


−	~~10. Name and save the offset specs to whatever you'd like.~~


		+	11. Name and save the offset specs to whatever you'd like.


Line 286:		Line 287:


−	~~11. Select the "'''OK'''" [[File:OK_button1.png]] button on the last window and the outline for the offset part will appear in the display area.~~


		+	12. Select the "'''OK'''" [[File:OK_button1.png]] button on the last window and the outline for the offset part will appear in the display area.


Line 298:		Line 299:


−		+	13. Select the "'''Connect'''" [[File:Exhaust_connect1.png]] button and click on each part in sequence from left to right to connect them.
−
−
−	12. Select the "'''Connect'''" [[File:Exhaust_connect1.png]] button and click on each part in sequence from left to right to connect them.

	[[File:Exh_partdefine2.png]]		[[File:Exh_partdefine2.png]]

@@ Line 303: / Line 303: @@
 . Select the "'''Connect'''" [[File:Exhaust_connect1.png]] button and click on each part in sequence from left to right to connect them.
-[[File:Exh_partconnect1.png]][[File:Exh_partdefine2.png]]
+[[File:Exh_partdefine2.png]]
 ==Creating a Tail Pipe==

@@ Line 1: / Line 1: @@
 '''This tutorial is designed to walk the user through the steps in making an exhaust system out of bent parts in the Exhaust interface. For initial information on the Exhaust interface, see [[Exhaust Design]]'''
@@ Line 320: / Line 322: @@
 [[File:Exh_grid_spacing4.png]]
 [[File:Exh_muffoffset5.png]]

@@ Line 319: / Line 319: @@
 . Then, start creating a new section starting at the end of the 6 inch pipe from the previous step. Before finishing the part though, change the "'''Grid Offset:'''" to "'''6'''" and then place the end of the pipe exactly 6 inches below and 6 inches left down the blue line as seen below.
 [[File:Exh_muffoffset5.png]]
 . Lastly, while still operating in the "'''New Section'''" function, select the end of the pipe and create one more "'''12''''" inch length of pipe.
-[[File:Exh_grid_spacing4.png]]
+[[File:Exh_muffoffset6.png]]
 '''The part is now complete.'''