Exhaust Tutorial II - Revision history

Fabcam1 at 19:39, 10 December 2014

2014-12-10T19:39:42Z

2014-12-05T18:20:43Z

2014-12-02T22:25:15Z

2014-12-02T22:21:43Z

2014-12-02T22:20:06Z

2014-12-02T22:19:01Z

2014-12-02T22:18:13Z

2014-12-02T22:17:35Z

2014-12-02T22:16:52Z

2014-12-01T20:08:56Z

← Older revision		Revision as of 19:39, 10 December 2014
Line 281:		Line 281:


−	"'''The offset is now complete and should look like the first picture below.'''"	+	'''The offset is now complete and should look like the first picture below.'''

	==Creating Exhaust Pipes==		==Creating Exhaust Pipes==

@@ Line 148: / Line 148: @@
 ==Creating an Offset Part==
-. Select the "'''New Section'''" button and place a length of pipe "'''24'''" inches long which runs directly through the front axle at 6 inches parallel to the blue line. (See below.)
+. Select the "'''New Section'''" button and place a length of pipe "'''24'''" inches long which runs directly through the rear axle at 6 inches parallel to the blue line. (See below.)
 [[File:exh_tut_offset99.png|center]]

← Older revision		Revision as of 22:25, 2 December 2014
Line 280:		Line 280:


		+
		+	"'''The offset is now complete and should look like the first picture below.'''"

	==Creating Exhaust Pipes==		==Creating Exhaust Pipes==

← Older revision		Revision as of 22:21, 2 December 2014
Line 227:		Line 227:


−	8. Type "'''1'''" in the "'''Top Width: A~~'''" value field and "'''20'''" in the "'''Bottom Width: B~~'''" value field to establish the ~~size and location~~ of the offset.	+	8. Type "'''20'''" in the "'''Top Width: A'''" value field to establish the width of the offset.


Line 263:		Line 263:


−	~~11. Name and save the offset specs to whatever you'd like.~~




		+	11. Name and save the offset specs to whatever you'd like.



−	~~12. Select the "'''OK'''" [[File:OK_button1.png]] button.~~


		+	12. Select the "'''OK'''" [[File:OK_button1.png]] button.

← Older revision		Revision as of 22:20, 2 December 2014
Line 190:		Line 190:

	4. Since the section is 24 inches, type "'''12'''" in the "'''Distance to Center:'''" value field for the location of the center bend.		4. Since the section is 24 inches, type "'''12'''" in the "'''Distance to Center:'''" value field for the location of the center bend.
−


Line 201:		Line 200:

	5. Select the "'''Next'''" [[File: Exhaust_next1.png]] button.		5. Select the "'''Next'''" [[File: Exhaust_next1.png]] button.
−
−


Line 259:		Line 256:


−	~~11. Name and save the offset specs to whatever you'd like.~~


		+
		+
		+
		+
		+
		+	11. Name and save the offset specs to whatever you'd like.

← Older revision		Revision as of 22:19, 2 December 2014
Line 175:		Line 175:

	4. Select the "'''3 Bends'''" option and select the "'''Next'''" [[File:Exhaust_next1.png]] button.		4. Select the "'''3 Bends'''" option and select the "'''Next'''" [[File:Exhaust_next1.png]] button.
−
−
−
−

← Older revision		Revision as of 22:18, 2 December 2014
Line 158:		Line 158:


−
−
−	~~3. Select the "'''Next'''" button [[File:Exhaust_next1.png]]~~




		+	3. Select the "'''Next'''" button [[File:Exhaust_next1.png]]

@@ Line 153: / Line 153: @@
 [[File:Exh_offset_steping1.png|right]]
 . Next, select the "'''Offset'''" [[File:Exhaust_offset1.png]] button, select the 2 foot section in order to create an offset part that bends up and over the axle.
@@ Line 165: / Line 161: @@
 . Select the "'''Next'''" button [[File:Exhaust_next1.png]]

@@ Line 150: / Line 150: @@
 . Select the "'''New Section'''" button and place a length of pipe "'''24'''" inches long which runs directly through the front axle at 6 inches parallel to the blue line. (See below.)
-[[File:exh_tut_offset99.png]]
+[[File:exh_tut_offset99.png|center]]
 [[File:Exh_offset_steping1.png|right]]
-. Next, select the "'''Offset'''" [[File:Exhaust_offset1.png]] button, select the 2 foot section, and create an offset part that bends up and over the axle.
+. Next, select the "'''Offset'''" [[File:Exhaust_offset1.png]] button, select the 2 foot section in order to create an offset part that bends up and over the axle.
@@ Line 161: / Line 197: @@
@@ Line 170: / Line 205: @@
 . Since the section is 24 inches, type "'''12'''" in the "'''Distance to Center:'''" value field for the location of the center bend.
@@ Line 179: / Line 216: @@
 . Select the "'''Next'''" [[File: Exhaust_next1.png]] button.

@@ Line 258: / Line 258: @@
 . First, select the "'''New Section'''" [[File:Exhaust_newsec1.png]] button and fill in the remaining "'''6'''" inches from the offset part to the catalytic converter.
-[[File:Exh_define_offset7.png]][[File:Exh_define_offset8.png]]
+[[File:Exh_define_offset6.png]][[File:Exh_define_offset8.png]]
 . Working on the other side of the catalytic converter now, create 5 separate length segments as shown below.