Harpoon 3D - Revision history

Fabcam1 at 18:14, 31 December 2015

2015-12-31T18:14:27Z

2015-12-31T17:59:20Z

2015-12-31T17:57:02Z

2014-12-10T20:41:00Z

2014-11-14T15:38:00Z

2014-11-07T19:53:36Z

2014-11-06T21:16:57Z

2014-11-06T20:26:55Z

2014-11-06T19:40:54Z

2014-11-06T18:31:55Z

← Older revision		Revision as of 18:14, 31 December 2015
Line 45:		Line 45:

	[[File:design_harpoon_5.png\|right]]		[[File:design_harpoon_5.png\|right]]
−	'''Once more than one angle is applied to a bend''' (Example: Pulled the light green harpoon point and then pulled the red harpoon point), the angle as well as the axis that the angle is along will be shown below the value fields in the left panel next to an axis icon. The colors of the small arrows on this icon correspond to the axes that the angle is along. These angle values can be also edited by entering values directly into the given fields.	+	'''Once more than one angle is applied to a bend''' (Example: Pulled the light green harpoon point and then pulled the red harpoon point), the angle as well as the axis that the angle is along will be shown below the value fields in the left panel next to an axis icon. The colors of the small arrows on this icon correspond to the axes that the angle is along. '''These angle values can be also edited by entering values directly into the given fields. The length of the straight can also be entered or edited in the "Length" field.'''

← Older revision		Revision as of 17:59, 31 December 2015
Line 44:		Line 44:


−	[[File:design_harpoon_5.png\|right~~\|600px~~]]	+	[[File:design_harpoon_5.png\|right]]
	'''Once more than one angle is applied to a bend''' (Example: Pulled the light green harpoon point and then pulled the red harpoon point), the angle as well as the axis that the angle is along will be shown below the value fields in the left panel next to an axis icon. The colors of the small arrows on this icon correspond to the axes that the angle is along. These angle values can be also edited by entering values directly into the given fields.		'''Once more than one angle is applied to a bend''' (Example: Pulled the light green harpoon point and then pulled the red harpoon point), the angle as well as the axis that the angle is along will be shown below the value fields in the left panel next to an axis icon. The colors of the small arrows on this icon correspond to the axes that the angle is along. These angle values can be also edited by entering values directly into the given fields.

← Older revision		Revision as of 17:57, 31 December 2015
Line 44:		Line 44:


−	[[File:~~design_harpoon_3~~.png\|right\|600px]]	+	[[File:design_harpoon_5.png\|right\|600px]]
	'''Once more than one angle is applied to a bend''' (Example: Pulled the light green harpoon point and then pulled the red harpoon point), the angle as well as the axis that the angle is along will be shown below the value fields in the left panel next to an axis icon. The colors of the small arrows on this icon correspond to the axes that the angle is along. These angle values can be also edited by entering values directly into the given fields.		'''Once more than one angle is applied to a bend''' (Example: Pulled the light green harpoon point and then pulled the red harpoon point), the angle as well as the axis that the angle is along will be shown below the value fields in the left panel next to an axis icon. The colors of the small arrows on this icon correspond to the axes that the angle is along. These angle values can be also edited by entering values directly into the given fields.

@@ Line 28: / Line 28: @@
-"'''These features are available in the Harpoon 3d stand alone interface.'''"
+'''These features are available in the Harpoon 3d stand alone interface.'''
 *'''To add a bend''' to the part, click the "'''Add Bend'''" [[File:add_bend.png]] button. Or hover over the end of the tube, and once the small green axis appears, double click. The new bend will be added and the harpoon tool will move to the end of the part.
 *'''To remove the last bend''', click the "'''Remove'''" [[File:harpoon_remove_bend2.png]] button.
-"'''These features are available in Assembly as an add-on and can be accessed under the "Design" tab.'''"
+'''These features are available in Assembly as an add-on and can be accessed under the "Design" tab.'''
 *'''To add a bend''' to the part, click the "'''Add Bend'''" [[File:add_bend.png]] button. Or hover over the end of the tube, and once the small green axis appears, double click. The new bend will be added and the harpoon tool will move to the end of the part.

@@ Line 31: / Line 31: @@
 *'''To add a bend''' to the part, click the "'''Add Bend'''" [[File:add_bend.png]] button. Or hover over the end of the tube, and once the small green axis appears, double click. The new bend will be added and the harpoon tool will move to the end of the part.
-*'''To remove the last bend''', click the "'''Remove'''" [[File:harpoon_remove_bend1.png]] button.
+*'''To remove the last bend''', click the "'''Remove'''" [[File:harpoon_remove_bend2.png]] button.
 "'''These features are available in Assembly as an add-on and can be accessed under the "Design" tab.'''"

@@ Line 20: / Line 20: @@
 .) By '''selecting a harpoon point and dragging it''' into place.
-.) By '''selecting a harpoon point and keying in''' the value.
+.) By '''selecting a harpoon point and typing in''' the value.
 .) By '''entering values''' directly into the fields.

@@ Line 1: / Line 1: @@
-'''"UNDER CONSTRUCTION: THANKS FOR YOUR PATIENCE'''"
 [[File:Material_Die3.png|right]]
 To draw a new part using the harpoon interface, first select the material and die.

← Older revision		Revision as of 18:31, 6 November 2014
Line 28:		Line 28:


		+	"'''These features are available in the Harpoon 3d stand alone interface.'''"
	'''To add a bend''' to the part, click the "'''Add Bend'''" [[File:add_bend.png]] button. Or hover over the end of the tube, and once the small green axis appears, double click. The new bend will be added and the harpoon tool will move to the end of the part.		'''To add a bend''' to the part, click the "'''Add Bend'''" [[File:add_bend.png]] button. Or hover over the end of the tube, and once the small green axis appears, double click. The new bend will be added and the harpoon tool will move to the end of the part.

	'''To remove the last bend''', click the "'''Remove'''" [[File:harpoon_remove_bend1.png]] button.		'''To remove the last bend''', click the "'''Remove'''" [[File:harpoon_remove_bend1.png]] button.

		+	"'''These features are available in Assembly and other interfaces that