My Material or Tooling Library won't Update - Revision history

Fabcam1 at 15:24, 6 October 2015

2015-10-06T15:24:07Z

Fabcam1 at 15:12, 6 October 2015

2015-10-06T15:12:59Z

Fabcam1 at 20:21, 5 June 2014

2014-06-05T20:21:58Z

Fabcam1 at 20:21, 5 June 2014

2014-06-05T20:21:13Z

Fabcam1 at 20:19, 5 June 2014

2014-06-05T20:19:16Z

Fabcam1 at 20:18, 5 June 2014

2014-06-05T20:18:07Z

Fabcam1 at 20:17, 5 June 2014

2014-06-05T20:17:15Z

Fabcam1: Created page with "My material or tooling library won't update. This is a common question and here is a list as to the reasons why: --> You must select the "Add New" button before entering the..."

2014-06-05T14:24:27Z

Created page with "My material or tooling library won't update. This is a common question and here is a list as to the reasons why: --> You must select the "Add New" button before entering the..."

New page

My material or tooling library won't update.

This is a common question and here is a list as to the reasons why:

--> You must select the "Add New" button before entering the tooling or material information.

When you enter in the material diameter or wall thickness, or the tooling clr, calibrated clr or bend location offset you MUST
Use a decimal place number.
No other characters like " or ' also do not use text like inch or mm
The material diameter must be greater than twice the wall thickness. many times a user will put in .95 instead of .095
In the material library the dimension under the "circle" is the OD of material.

--> It is okay to leave the weight in the material library as 0

--> When finished select the "Apply" button. This will update the list on the left hand side.

--> After you select the "Apply" button, the "OK" button is used to update the list to the hard drive. SELECT THE "OK" BUTTON WHEN FINISHED.

@@ Line 8: / Line 8: @@
 *No other characters such as symbols or abbreviations. Also do not use text like inches or mms.
 *The material diameter must be greater than twice the wall thickness. Many times a user will put in .95 instead of .095
-*In the material library the dimension under the '''"circle"''' is the OD of material.
+*In the material library the dimension under the '''circle''' is the OD of material.
 --> It is okay to leave the weight in the material library as 0.
@@ Line 14: / Line 14: @@
 --> When finished select the '''"Apply"''' button. This will update the list on the left hand side.
---> After you select the '''"Apply"''' button, the "OK" button is used to update the list to the hard drive. '''SELECT THE "OK" BUTTON WHEN FINISHED.'''
+--> After you select the '''"Apply"''' button, the '''"OK"''' button is used to update the list to the hard drive. '''SELECT THE "OK" BUTTON WHEN FINISHED.'''

@@ Line 1: / Line 1: @@
-My material or tooling library won't update.
+My material or die library won't update.
 This is a common question and here is a list as to the reasons why:
---> You must select the "Add New" button before entering the tooling or material information.
+--> You must select the '''"Add New"''' button before entering the tooling or material information.
-*When you enter in the material diameter or wall thickness, or the tooling clr, calibrated clr or bend location offset you MUST
+*When you enter in the material diameter or wall thickness, or the achieved clr, calibrated clr or bend location offset you '''MUST''' use a decimal place number.
-*Use a decimal place number.
+*No other characters such as symbols or abbreviations. Also do not use text like inches or mms.
-*No other characters like " or ' also do not use text like inch or mm
+*The material diameter must be greater than twice the wall thickness. Many times a user will put in .95 instead of .095
-*The material diameter must be greater than twice the wall thickness. many times a user will put in .95 instead of .095
+*In the material library the dimension under the '''"circle"''' is the OD of material.
---> It is okay to leave the weight in the material library as 0
+--> It is okay to leave the weight in the material library as 0.
---> When finished select the "Apply" button. This will update the list on the left hand side.
+--> When finished select the '''"Apply"''' button. This will update the list on the left hand side.
---> After you select the "Apply" button, the "OK" button is used to update the list to the hard drive. '''SELECT THE "OK" BUTTON WHEN FINISHED.'''
+--> After you select the '''"Apply"''' button, the "OK" button is used to update the list to the hard drive. '''SELECT THE "OK" BUTTON WHEN FINISHED.'''

@@ Line 6: / Line 6: @@
 *When you enter in the material diameter or wall thickness, or the tooling clr, calibrated clr or bend location offset you MUST
-    Use a decimal place number.
+*Use a decimal place number.
-    No other characters like " or ' also do not use text like inch or mm
+*No other characters like " or ' also do not use text like inch or mm
-    The material diameter must be greater than twice the wall thickness. many times a user will put in .95 instead of .095
+*The material diameter must be greater than twice the wall thickness. many times a user will put in .95 instead of .095
-    In the material library the dimension under the "circle" is the OD of material.
+*In the material library the dimension under the "circle" is the OD of material.
 --> It is okay to leave the weight in the material library as 0

@@ Line 5: / Line 5: @@
 --> You must select the "Add New" button before entering the tooling or material information.
-     *When you enter in the material diameter or wall thickness, or the tooling clr, calibrated clr or bend location offset you MUST
+     **When you enter in the material diameter or wall thickness, or the tooling clr, calibrated clr or bend location offset you MUST
-     *Use a decimal place number.
+     **Use a decimal place number.
-     *No other characters like " or ' also do not use text like inch or mm
+     **No other characters like " or ' also do not use text like inch or mm
-     *The material diameter must be greater than twice the wall thickness. many times a user will put in .95 instead of .095
+     **The material diameter must be greater than twice the wall thickness. many times a user will put in .95 instead of .095
-     *In the material library the dimension under the "circle" is the OD of material.
+     **In the material library the dimension under the "circle" is the OD of material.
 --> It is okay to leave the weight in the material library as 0