Panel - Revision history

Fabcam1 at 15:40, 10 September 2014

2014-09-10T15:40:12Z

Fabcam1 at 15:38, 10 September 2014

2014-09-10T15:38:55Z

Fabcam1 at 16:53, 13 June 2014

2014-06-13T16:53:19Z

Fabcam1 at 16:11, 13 June 2014

2014-06-13T16:11:37Z

Fabcam1: Created page with "'''Bend-Tech 7x Wiki :: Assembly :: Edit :: Panel''' NOTOC right In the panel tab, plate panels can be..."

2014-06-10T19:01:49Z

Created page with "'''Bend-Tech 7x Wiki :: Assembly :: Edit :: Panel''' __NOTOC__ right In the panel tab, plate panels can be..."

New page

'''[[Main Page|Bend-Tech 7x Wiki]] :: [[Assembly]] :: [[Assembly - Edit|Edit]] :: Panel'''
__NOTOC__
[[File:assembly_panel.png|right]]

In the panel tab, plate panels can be created by defining their location on an assembly.

To create a panel, first click the '''Select Tubes''' button [[File:select_tubes.png]]. Next, select sections of tube on the assembly that are on the same plane to define the outline of the panel (a minimum of 2 tubes is required). Once all the necessary tubes are selected, click the '''Complete''' button. [[File:complete.png]]

The parts will then be listed in the chart below. The corner and value specifications will need to be supplied for the corners and the wrap value will need to be given for the edges of the panel.

'''Corner'''

*Connect:

*Intersection:

*Radius:

*Chamfer:

*Notch:

The '''Wrap''' value determines how far the material will overlap the edge of the tube. This value is given in terms of degrees.

Once these values/options have been defined, click the '''Create Plate''' button. [[File:create_plate.png]] Give the panel and name and choose a plate material. Click the '''OK''' button to create the panel.

@@ Line 8: / Line 8: @@
 To create a panel, first click the '''Select Tubes''' button [[File:select_tubes.png]]. Next, select sections of tube on the assembly that are on the same plane to define the outline of the panel (a minimum of 2 tubes is required). When selecting tubes, be sure to select the '''''starting end''''' of the tube. Once all the necessary tubes are selected, click the '''Complete''' button. [[File:complete.png]]
 [[File:panel_order.png]]
 The parts will then be listed in the chart below. The corner and value specifications will need to be supplied for the corners and the wrap value will need to be given for the edges of the panel.

← Older revision		Revision as of 15:38, 10 September 2014
Line 8:		Line 8:

	To create a panel, first click the '''Select Tubes''' button [[File:select_tubes.png]]. Next, select sections of tube on the assembly that are on the same plane to define the outline of the panel (a minimum of 2 tubes is required). When selecting tubes, be sure to select the '''''starting end''''' of the tube. Once all the necessary tubes are selected, click the '''Complete''' button. [[File:complete.png]]		To create a panel, first click the '''Select Tubes''' button [[File:select_tubes.png]]. Next, select sections of tube on the assembly that are on the same plane to define the outline of the panel (a minimum of 2 tubes is required). When selecting tubes, be sure to select the '''''starting end''''' of the tube. Once all the necessary tubes are selected, click the '''Complete''' button. [[File:complete.png]]
		+
		+	[[File:panel_order.png]]

	The parts will then be listed in the chart below. The corner and value specifications will need to be supplied for the corners and the wrap value will need to be given for the edges of the panel.		The parts will then be listed in the chart below. The corner and value specifications will need to be supplied for the corners and the wrap value will need to be given for the edges of the panel.

← Older revision		Revision as of 16:53, 13 June 2014
Line 22:		Line 22:
	To adjust the panel after it has been created, just change any of the options and click the '''Create Plate''' button to update the panel.		To adjust the panel after it has been created, just change any of the options and click the '''Create Plate''' button to update the panel.

		+
		+	To do more in depth edits with the plate, such as adding holes, click the '''Edit Plate''' button to bring the plate into the [[Plate]] design interface. Once the edits are complete, the plate can be sent back into the assembly by using the '''Transfer''' menu [[File:transfer.png]] and selecting the current assembly project. The plate will be brought back in and placed in its original location on the tube(s).