PickPoints - 2 Points - Revision history

Fabcam1 at 14:52, 30 September 2015

2015-09-30T14:52:43Z

Fabcam1 at 14:51, 30 September 2015

2015-09-30T14:51:07Z

Fabcam1 at 16:46, 5 June 2014

2014-06-05T16:46:35Z

Fabcam1: Created page with " The PickPoint - 2 Points method allows for a point to be located "x" number of millimeters or inches down a line. Step 1) Select the "'''PickPoints'''" tab, then the "'''Ref..."

2014-06-04T20:59:06Z

Created page with " The PickPoint - 2 Points method allows for a point to be located "x" number of millimeters or inches down a line. Step 1) Select the "'''PickPoints'''" tab, then the "'''Ref..."

New page

The PickPoint - 2 Points method allows for a point to be located "x" number of millimeters or inches down a line.

Step 1) Select the "'''PickPoints'''" tab, then the "'''Reference'''" tab.

Step 2) Select the "'''Set Line'''" command button under '''Two Points'''.

Step 3) '''Select a "PickPoint"''' for the start end of the line. Note: The distance value will be determined from this end.

Step 4) '''Select the 2nd "PickPoint"''' representing the line.

Step 5) Enter the value into the "'''Move Amount'''" field. You will see a Purple point at this location.

Step 6) Select the "'''Apply'''" command.

[[File:TwoPoints.png|700px]]

@@ Line 6: / Line 6: @@
 '''Step 2:''' Select the "'''Set Reference'''" command button under '''Two Points'''.
-'''Step 3:''' '''Select a "PickPoint"''' for the start end of the line. Note: The distance value will be determined from this end.
+'''Step 3:''' Select a '''"PickPoint"''' for the start end of the line. Note: The distance value will be determined from this end.
-'''Step 4:''' '''Select the 2nd "PickPoint"''' representing the line.
+'''Step 4:''' Select the 2nd '''"PickPoint"''' representing the line.
 '''Step 5:''' Enter the value into the "'''Move Amount'''" field. You will see a Purple point at this location.

@@ Line 2: / Line 2: @@
 The PickPoint - 2 Points method allows for a point to be located "x" number of millimeters or inches down a line.
-Step 1) Select the "'''PickPoints'''" tab, then the "'''Reference'''" tab.
+'''Step 1:''' Select the "'''PickPoints'''" tab, then the "'''Reference'''" tab.
-Step 2) Select the "'''Set Reference'''" command button under '''Two Points'''.
+'''Step 2:''' Select the "'''Set Reference'''" command button under '''Two Points'''.
-Step 3) '''Select a "PickPoint"''' for the start end of the line. Note: The distance value will be determined from this end.
+'''Step 3:''' '''Select a "PickPoint"''' for the start end of the line. Note: The distance value will be determined from this end.
-Step 4) '''Select the 2nd "PickPoint"''' representing the line.
+'''Step 4:''' '''Select the 2nd "PickPoint"''' representing the line.
-Step 5) Enter the value into the "'''Move Amount'''" field. You will see a Purple point at this location.
+'''Step 5:''' Enter the value into the "'''Move Amount'''" field. You will see a Purple point at this location.
-Step 6) Select the "'''Apply'''" command.
+'''Step 6:''' Select the "'''Apply'''" command.
 [[File:TwoPoints.jpg|700px]]