Using Spring Charts - Revision history

Fabcam1 at 14:39, 6 October 2015

2015-10-06T14:39:41Z

2015-10-06T14:37:59Z

2015-10-06T14:33:18Z

2014-06-05T20:13:54Z

2014-06-05T19:02:21Z

2014-06-05T19:00:31Z

2014-06-05T18:58:56Z

2014-06-05T18:55:32Z

2014-06-05T18:53:32Z

2014-06-05T18:49:02Z

← Older revision		Revision as of 14:39, 6 October 2015
Line 6:		Line 6:


−	Once you enter into the Spring Charts screen you will see everything is blank. Select a die from the list to add spring back values to and click the '''"Add"''' button from the chart in the center of the window.	+	Once you enter into the Spring Charts screen you will see everything is blank. Select a die from the list to add spring back values to and click the '''"Add New"''' button from the chart in the center of the window.

	[[File:SpringCharts5.jpg]]		[[File:SpringCharts5.jpg]]

← Older revision		Revision as of 14:37, 6 October 2015
Line 6:		Line 6:


−	Once you enter into the Spring Charts screen you will see everything is blank. Select a die from the list to add spring back values to and click the "Add" button from the chart in the center of the window.	+	Once you enter into the Spring Charts screen you will see everything is blank. Select a die from the list to add spring back values to and click the '''"Add"''' button from the chart in the center of the window.

	[[File:SpringCharts5.jpg]]		[[File:SpringCharts5.jpg]]

@@ Line 1: / Line 1: @@
-For SE customers you have the function of Spring Charts. These allow you to put in a couple (from 2 to 20) sets of bend angles vs. spring angles and the software will calculate and display the angles for a part.
+SE users have the function to use '''"Spring Charts"'''. These allow you to put in a couple (from 2 to 20) sets of bend angles vs. spring angles and the software will calculate and display the angles for a part.
-To set up the Spring Charts, go to the "Die Library" window under your "Tools" pull down menu. Select "Spring Back" button near the bottom left corner of the window.
+To set up the Spring Charts, go to the '''"Die Library"''' window under your '''"Tools"''' pull down menu. Select the '''"Spring Back"''' button near the bottom left corner of the window.
 [[File:SpringCharts1.jpg|500px|]]
@@ Line 21: / Line 21: @@
-When in a part, select the "Display Spring Angle" check box in your tooling tab.
+When in a part, select the '''"Display Spring Angle"''' check box in your tooling tab.
 [[File:SpringCharts6.jpg]]

← Older revision		Revision as of 20:13, 5 June 2014
Line 11:		Line 11:


−	Fill in the "Desired Angle" and the "Spring Angle".	+	Fill in the '''"Desired Angle"''' and the '''"Spring Angle"'''.

	[[File:SpringCharts3.jpg]]		[[File:SpringCharts3.jpg]]

@@ Line 8: / Line 8: @@
 Once you enter into the Spring Charts screen you will see everything is blank. Select a die from the list to add spring back values to and click the "Add" button from the chart in the center of the window.
-[[File:SpringCharts2.jpg]]
+[[File:SpringCharts5.jpg]]
@@ Line 23: / Line 23: @@
 When in a part, select the "Display Spring Angle" check box in your tooling tab.
-[[File:SpringCharts5.jpg]]
+[[File:SpringCharts6.jpg]]

@@ Line 8: / Line 8: @@
 Once you enter into the Spring Charts screen you will see everything is blank. Select a die from the list to add spring back values to and click the "Add" button from the chart in the center of the window.
+Fill in the "Desired Angle" and the "Spring Angle".
 [[File:SpringCharts3.jpg]]
-Once you have filled in atleast 2 sets of values the chart will fill in on the right side.
+Once you have filled in at least 2 sets of values the chart will fill in on the right side.
 [[File:SpringCharts4.jpg]]

← Older revision		Revision as of 18:58, 5 June 2014
Line 8:		Line 8:
	Once you enter into the Spring Charts screen you will see everything is blank. Select a die from the list to add spring back values to and click the "Add" button from the chart in the center of the window.		Once you enter into the Spring Charts screen you will see everything is blank. Select a die from the list to add spring back values to and click the "Add" button from the chart in the center of the window.

−	~~[[File:SpringCharts2.jpg]]~~	+

← Older revision		Revision as of 18:53, 5 June 2014
Line 6:		Line 6:


−	Once you enter into the Spring Charts screen you will see everything is blank. Select a die from the list to add spring back values to and click the "Add" button from the chart in the ~~upper left hand corner~~.	+	Once you enter into the Spring Charts screen you will see everything is blank. Select a die from the list to add spring back values to and click the "Add" button from the chart in the center of the window.

	[[File:SpringCharts2.jpg]]		[[File:SpringCharts2.jpg]]

← Older revision		Revision as of 18:49, 5 June 2014
Line 3:		Line 3:
	To set up the Spring Charts, go to the "Die Library" window under your "Tools" pull down menu. Select "Spring Back" button near the center of the window.		To set up the Spring Charts, go to the "Die Library" window under your "Tools" pull down menu. Select "Spring Back" button near the center of the window.

−	[[File:SpringCharts1.jpg]]	+	[[File:SpringCharts1.jpg\|500px\|]]