Dynatorch Dragon Guide

From Bend-Tech 7x Wiki
Revision as of 16:07, 6 March 2017 by Fabcam1 (talk | contribs)
Jump to: navigation, search

Take advantage of this page's Table Of Contents to find what section/item you're looking for information on.

Overview - Start Up

After receiving the Dragon software, all users will have to register the product with their personal identification along with a Dragon Serial number and Keycode (provided).

Registration1.png

Upon initial startup, the software will display a splash screen and open to the Dragon Task Menu. Here, you will have the options from the Main Menu Bar above along with creating straight parts with the Straight Part coping designer.

Dyna Dragon Menu1.png

Tube Library

We first advise you to enter material information into the Tube Library (located to the right of the Task Menu screen in the Library section) in order to designate what material you will be working with on a particular job. Only after a material is added to the Tube Library can you create a part in the Straight Part coping designer.

General

Tube Library2.png

Material Properties

Drag Tube General Tab2.png

Material Name:

  • This title will be used to refer to the material throughout the software. It is recommended to give each a unique, descriptive name to more easily identify each material.

Weight (per inch):

  • The weight of the material per unit can be supplied here. This value is completely optional, but it will be used to calculate the total weight of the part in the part designer interfaces above the results table.

Color:

  • The color of the material can be chosen using the Color button. Color button.png This color will be used to shade the material in various areas throughout the software.

Type:

  • Tube material can be either round, square, or rectangle.

Units:

  • Parts can be measured in either inches or millimeters.

Polyline Resolutions:

Drag Tube General Tab3.png

Max Length:

  • This is where the user will enter the maximum length for each segment in a polyline. A segment will be ignored if it is longer than this value. If the segment is shorter, it may be combined with an adjacent segment to create a single segment.

Max Angle:

  • This is where the user will enter the maximum angle between two segments in a polyline. If the angle is smaller than this value, the two segments may be combined to create a single segment.

Max Offset:

  • This is where the user will enter the maximum boundary offset for a polyline. If the combination of two line segments breaches the boundary defined by this value, the features will not be combined.

Wall Thickness, Diameter, and Height:

  • Depending on the type of material chosen, there will be different dimensions that will need to be supplied. If the material is round or square, the wall thickness and diameter measurements will be required. These values will be entered into the fields on the material diagram. If the material is rectangular, the wall thickness, diameter/width, and height will need to be provided. Note: The diameter/width and height of all materials are measured from the outside edges.

Mat lib 1.pngMat lib 2.png


Machine Settings

Machine Settings2.png

We recommend watching the video at the link below in order to understand what material settings should be applied for a typical entry. This has proven to be very helpful to many of our customers.

Material Machine Settings Video

Standard Material Machine Settings

NOTE: Machine Settings for Dynatorch users will not include the same options for Dragon machine owners. Your settings will only include the following options:

  • Kerf Width
  • Minimum Web
  • Default (stock) Length
  • Cutting Overlap
  • Cutting Height
  • Pierce Height
  • Cutting Feed Rate
  • Rotation RPM

These settings can be found in your cut charts in your torch manual... Any Thermal Dynamics torch inquiries will be re-directed to the Thermal Dynamics manufacturer as we do not offer technical support on their hardware.

LeadIn/Out Defaults

LeadIn Out Defaults2.png

Start/End Cut Lead Defaults: Ignite Settings

  • These settings are completely user specified and can vary based on the user's preference.

Drag Ignite Settings1.png

-Suggested Settings-

Ignite Type:

  • This is where the user will select the type of lead-in ignite type that will be set to this material by default. Arc with Angle is our preferred method. This means that the torch will initiate its cut into the material at an angle which will ease into an arc and then to the intended cut profile. This is a smooth ignite type and leaves little chance for error.

Dwell Time(sec):

  • This indicates how long the torch will remain on one place during the pierce. This can differ based on your torch and material type and thickness. Refer to your hypertherm manual for an exact time. Links to manuals are located at the bottom of this page.

Length/Distance:

  • This is the length of the line that eases into the actual cut profile. We can keep this relatively short. We recommend .125 in most cases.

Angle/Sweep:

  • This will be the angle at which the initial cut eases into the intended cut. We recommend a 45 degree angle for the ignite cut.

Radius:

  • This is where the user will enter the radius of the arc that channels into the cut profile. We recommend keeping this at around .125 as a preference.

Start/End Cut Lead Defaults: Extinguish Settings

  • These settings are completely user specified and can vary based on the user's preference.

Drag Extinguish Settings1.png

-Suggested Settings-

Extinguish Type:

  • This is where the user will select the type of lead-out extinguish type that will be set to this material by default. Perpendicular is our preferred method. This means that the torch will extinguish its cut at a perpendicular angle after the cut profile has been performed. This is a extinguish type that leaves the cut profile smoothly at a 90 degree angle.

Dwell Time(sec):

  • This indicates how long the torch will remain on one place during the extinguishing stage of the torch. This can be set to 0.

Length/Distance:

  • This is the length of the line that eases out of the cut profile. We can keep this relatively short. We recommend .125 in most cases.

Angle/Sweep:

  • Opposite of the ignite type section, this will be the angle at which the cut eases out of the intended cut. This will be greyed out when the perpendicular extinguish type is set as a default.

Radius:

  • This is where the user will enter the radius of the arc that channels out of the cut profile. This will be greyed out when the perpendicular extinguish type is set as a default.

Other Cut Lead Defaults

  • All other cut lead defaults can be set like the original cut lead defaults. These are meant for all cuts other that the start and end cuts of a part.

Drag Default Ignite And Extinguish Settings1.png

Straight Part Designer

Dragon Straight Part(2).png
Dragon Straight Part(3).png
  • Clicking on this option will allow the user to create a straight part with either flat, coped or mitered end cuts. This option will also let the user account for rotation, angles and offsets for the tube ends.















Action Tabs

Select Material

  • The Select Material:" drop down menu is where users will choose their desired material.

Click the small Folder icon Foler Icon1.png here to access your material library and select your material that way.

Click on the small Sort List icon List Icon1.png here to access your materials by your sorted lists.

Dragon Select Material(1).png

Cut Start / Cut End

The "Cutting" tab will determine the cuts on the starting of the tube and the cuts on the ending of the tube. Multiple cut nodes can be preformed to create any number of unique cut profiles.

Dragon Cut Start(2).png

  • Click on the "Add" Add New Cut1.png button to add a new cut to the tube/pipe created.
  • With a cut selected from the cut list, click on the "Remove" Remove The Cut1.png button to remove it from the design.
  • The "Location" section shows the location of the newly added cut (Start, or End). This location can be switched simply by clicking on the "Location" Location Of Cut1.png button or by double clicking the list item section itself.
  • The "Type" section gives users the option to choose a type of cut from "Cope/Notch" and "Miter". This type of cut can be switched simply by clicking on the "Type" Type Of Cut1.png button or by double clicking the list item section itself.
  • The "Material" section is a drop down menu that will give users the option to choose the size of tube that the current part will be intersecting with. This will adjust the size of the end cope(s) or miter cut profile(s).
  • The degree of rotation entered into the "Rotation" field will determine the rotation of the cut on either the start or end of the tube.
  • The degree of angle entered into the "Angle" field will determine the angle of the cut on either the start or end of the tube.
  • The degree of offset entered into the "Offset:" field will determine how the intersecting tube is offset from the start or end of the tube.
  • The value entered into the "Cut-Off (Start):" field will determine how many extra units (inches or millimeters) of tubing will be added to the start of the tube.
  • The value entered into the "Cut-Off (End):" field will determine how many extra units (inches or millimeters) of tubing will be added to the end of the tube.
  • The "Dimension Style" gives the user the option to choose the dimension of the cope/notch or miter from "Inside", "Center" and "Outside" dimensions as it pertains to the diameter of the tubing.
  • Checking the "Display Cross Tubes" check box will cause the intersecting cross tube to appear in the display screen.

Holes

Dragon Holes Create2.png

Shape

  • Round: Select Round, enter a diameter in the Width: field, and use the Hole Location section to determine where the round hole will be placed on the tube.
  • Oval: Select Oval, enter a width and height in the Width: and Height: fields, and use the Hole Location section to determine where the oval hole will be placed on the tube.
  • Square: Select Square, enter a width in the Width: field. If you want to automatically round the corners of the square, you can enter a value in the Corner: field. Entering 0 in the Corner field will result in square corners. Then, use the Hole Location section to determine where the square hole will be placed on the tube.
  • Ellipse: Select Ellipse and enter a width and height in the Width: and Height: fields, and use the Hole Location section to determine where the elliptical hole will be placed on the tube.
  • Rectangle: Select Rectangle and enter a width and height in the Width: and Height: fields and enter a value in the Corner: field. Entering 0 in the Corner field will result in square corners. Then, use the Hole Location section to determine where the rectangular hole will be placed on the tube.
  • Hole Dimensions

  • Width: Enter the width of the hole in this text field.
  • Height: Enter the height of the hole in this text field.
  • Corner: Enter the corner radius of the hole in this text field.
  • Hole Location

  • Leg: Choose the leg on which the hole will be placed in this text field.
  • Distance: Enter the distance that the hole will be from the start of the selected leg in this text field. Note: If Leg 1 is selected, the distance will be from the start of the tube. If any other leg is selected, the distance will take place from the end of the leg's previous bend.
  • Rotation: Enter the rotation of the hole in this text field. This rotation value will be based from the previous bend's inside radius.
  • Travel Check this check box and the location of the hole placed will be based from the start of the tube and not the distance from the previous bend.
  • Opposite Check this check box and the hole placed will be located on both sides of the tubing at the designated distance.
  • Action Buttons

  • Add Click the Add Add New Cut1.png button and enter the information for the hole details in the list to create the hole in your design.
  • Remove Click the Remove Remove The Cut1.png button and the selected hole will be removed from the list and from the design.
  • Copy Click the Copy Copy The Hole1.png button and the selected hole be copied and duplicated in the holes list. Doing this will make it much easier to set a similar hole in the design if you only need to change a few of the dimensions, or location settings.